Category: "Miniatures"

Range hood lighting

by brae  

I had built a lip on the bottom of my range hood to give a more realistic look and to have room to add a light.

I chose an LED strip in warm white by Novalyte, cutting a rough hole in the balsa to hold the light in place.  These lights are compatible with 12V dollhouse lighting.  I drilled a hole through to the back; the wires will run through the wall and plug into the power strip.

Here is the light in the mockup phase to check the fit.

Lights out!  This is exactly the look I wanted.

Spice rack

by brae  

I wanted a wall mounted spice rack, but I wasn't sure how to go about making the little spice jars to go in it.  I considered using beads for the base and perhaps polymer clay to make the caps, but I couldn't really find anything that matched the idea I had in my head.  Most things were either too large or not the right color, texture or shape.

What I ended up using was 3/16" diameter rigid aquarium tubing for the jars and 3/16" diameter wooden beads for the caps.

I cut 3/8" lengths of the tubing using a sharp X-Acto knife and a lot of patience.

I painted part of the inside with colors matching the various spices I wanted to mimic.

I didn't seal the bottoms since the jars would be displayed either in a rack or standing upright on a countertop, and since they were merely painted, there was nothing to spill out.

I created labels in Word using clip art borders for the design.  These measure just 1/4" square but they are legible.  I printed them on Avery label paper since I figured I'd get more glue on myself than on the tiny labels if I tried applying an adhesive after cutting them out.

I cut out each label along the lines and found it relatively easy to pull the backing off even though the paper was so tiny.  Using the sticky label paper made it very easy to attach the nameplates to the miniature bottles.  I then glued on the wooden beads to the serve as caps; I liked the existing reddish color so I decided to leave them as is.  The hole in the top didn't bother me since the jars wouldn't normally be viewed directly from above.  From the front perspective, the hole seems like a design detail.

Once the jars were made, I built a spice rack out of basswood and mini dowels, leaving it unfinished for now since I like the color.   I will likely seal it but not paint it.  Here you can also see the finished backsplash; I used two light coats of metallic silver paint that I wiped off before drying to create variegated shades of silver.

Update: The custom made spice rack with jars is now available in my etsy shop.

Kitchen sink

by brae  

The kitchen sink that came with the Euro Mini's sink cabinet was very shallow and not exactly what I wanted.

The hole in the top of the cabinet for the sink was deep, so there was plenty of room to add a deeper sink.  My attempts at making a sink out of polymer clay were lumpy and rather sad.  :(  So, I built one out of 1/8" basswood and balsa.

I first measured and cut the vertical pieces to fit inside the opening in the cabinet.  I then glued them onto a thin sheet of balsa using a jig.  Before enclosing the box, I used a metal sewing eyelet to punch a hole for a drain.

Once the basic box was dry, I cut the balsa base to fit and drilled a hole in the base cabinet to match up with the drain.

Using 1/4" half round strip wood, I built a frame for the top of the sink box.

I used a tiny bit of spackle to fill in any gaps between the frame and the box.

I watered down the paint so the finish would dry without any brush marks, sanding in between coats to remove any imperfections that would give away the fact that the sink is wood and not porcelain.  Once the paint finish was dry, I added a couple of coats of gloss sealer (Delta Ceramcoat gloss varnish).  To get the effect in the bottom of the sink, I let the gloss sealer pool.  I also covered it after applying the gloss to keep dust from settling on the finish.

UPDATE (01-12-10)
Alas, the above sink is no more.  :(  The gloss varnish cracked and yellowed in the thicker areas when it dried.  I had used it on the faux granite without a problem.  Thin coats of this varnish work great.

I made a second sink, and this time I used Triple Thick Brilliant Brush-On Gloss Glaze by DecoArt for the finish.

The finish turned out like porcelain again, though the glaze was definitely thick and not easy to use.  You have to work fast because it dries so fast.  I am pleased with the second sink but disappointed that the varnish I had used ruined the first.

Here the sink is installed in the cabinet with the sewing eyelet drain pressed into place.  Crisis averted!  :D

Update 02-20-10:
Well, I spoke too soon.  The second varnish (Triple Thick Brilliant Brush-On Gloss Glaze by DecoArt) turned yellow, too.  There are big letters on the front of the package that read, "Non-Yellowing," so I don't know what happened.

I wasn't going to give up on the second sink without trying to fix it first.  I removed it from the cabinet, removed the hardware and gave it two coats of Krylon indoor/outdoor gloss white spray paint.  It worked!  :D

1 ... 21 22 23 24 25 26 ...27 ...28 29 30 32